fbpx

CONTINUOUS MIXING SYSTEMS

D2W CONTINUOUS MIXER

D2W GAS POWERED CONTINUOUS MIXER

D2W WORKHORSE

D2W CONTINUOUS MIXER

D2W dry to wet

CONTINUOUS OUTPUT. CONSTANT QUALITY.

The SPEC MIX® D2W is the ultimate SPEC MIX silo material mixing system that provides contractors the flexibility and control they need for staging and managing their product needs.

It functions like a miniature on-site batch plant that reduces labor and clean up, eliminates material waste, produces highly consistent product, and above all maximizes the productivity of any size crew. From masonry mortars, grouts, stucco and shotcrete formulas, the SPEC MIX D2W system is a contractor’s ideal solution for higher production and profitability.

Specifically designed to attach to a SPEC MIX G7000 or Ten Bagger silo, this continuous power mixing auger system utilizes a unique array of specialized mixing paddles and agitators. It folds and sheers any preblended cementitious product to efficiently hydrate the dried aggregate and mechanically work natural air into the material for maximum workability, open time and boardlife.

The patented mixing chamber, shaft and paddles resist cement sticking to them and the preset wash-out cycle allows the SPEC MIX D2W to self-clean in 2 minutes; there is no need to disassemble the mixer. There is no sand to shovel; bags to lift and risk of back injury and certainly no trash or dust at the mixer. If the project requires colored mortar, dry-pack deck mud, coarse grout or concrete repair products, the SPEC MIX D2W will produce the product quickly and consistently—all day, every day and it’s all done with the flip of a switch. With SPEC MIX you work smarter not harder!

D2W Continuous Mixing System Specifications
Power Requirements• Single Phase 230V, 50A (Consult electrician for main power hook-up, typically use 8 ga or sometimes 6 ga wire depending on length of run)
Generator Requirements (if used)• Minimum 18Kw
Electric Control Panel• UL rated components
• NEMA 4 rated weather resistant enclosure
• Manual or remote control operation
Motor• 5 HP electric
Water Pump Panel• Flow adjustable from 1 to 15 GPM (3.7 to 56.7 LPM)
Water Requirements• Pressurized Water - Use a 1 in (25 mm) diameter hose with 3/4 in (19mm) ends
• Standing water - Use a 200 gallon (257 L) container (minimum)
Wet Mix Output (approximate)• 1/2 Pitch Screw: 3.5 to 5 cu yd (2.6 to 3.8 m³)/hr
• 3/4 Pitch Screw: 5.5 to 7 cu yd (4.2 to 5.3 m³)/hr
• Full Pitch Screw: 7.5 to 9 cu yd (5.7 to 6.8 m³)/hr
* Based on current D2W configuration. D2W specifications may change slightly due to the model year of manufacture. Confirm the D2W specifications with your SPEC MIX representative.
SPEC MIX D2W Continuous Mixing System

D2W GAS POWERED CONTINUOUS MIXER

D2W Gas Powered Hydraulic Drive

WORK ANYWHERE – MIX CONTINUOUSLY!

The SPEC MIX® D2W Continuous Mixing System with its Gas Powered Hydraulic Drive is the portable batch plant giving contractors the ability to mix large amounts of materials anywhere without needing any utilities—no electricity and no pressurized water line! Simply connect the D2W’s hose to its pump and a 200 gallon tank of clean water, start the gas powered hydraulic drive and the D2W Continuous Mixing System is capable of producing up to 10 cubic yards of material per hour. Once the water ratio is set the D2W continuously produces highly consistent, workable product with optimal open-time.

It’s the ultimate SPEC MIX Silo System that provides contractors the ability to complete projects in any remote location and the flexibility to mix most any SPEC MIX product whenever it’s needed. Whether the project calls for masonry mortar and grout, concrete, stucco or specialty products, the D2W Gas Powered system will mix around the clock quickly with zero waste—all day, every day—and it’s all done with the flip of a switch.

Having your own on-site, on-demand material production source greatly decreases labor and eliminates material waste while maximizing the efficiency, productivity and profitability of any size crew. There is no sand to shovel; bags to lift and risk of back injury and certainly no trash or dust at the mixer. The SPEC MIX D2W Continuous Mixing System & Gas Powered Hydraulic Drive unit gives you control when, where and how fast the job is completed!

D2W Gas Powered Continuous Mixer Specifications
Control Panel• UL rated components
• NEMA 4 rated weather resistant enclosure
• Manual control operation
Motor• 13 HP Honda electric start
Water Requirements• Pressurized Water - Use a 1 in (25 mm) diameter water hose with 3/4 in (19 mm) ends
• Standing water - Use a 200 gallon (757 L) container (minimum)
D2W Output• 1/2 Pitch Screw: 3.5 to 5 cu yd (2.6 to 3.8m3)/hr
•3/4 Pitch Screw: 5.5 to 7 cu yd (4.2 to 5.3 m3)/hr
• Full Pitch Screw: 7.5 to 10 cu yd (5.7 to 6.8 m3)/hr

D2W WORKHORSE

workhorse

MIX WHERE YOU WORK – CONTINUOUSLY!

The SPEC MIX® D2W Workhorse Continuous Mixing System is powered by a standard 120V circuit so you mix SPEC MIX products anywhere on site. Simply plug into a power outlet, connect to a strong and steady water source then flip on the switch and start breaking bags of SPEC MIX products for continuous, consistently mixed materials. This lightweight, highly mobile mixer puts out up to 1.5 cubic yards of mix per hour or small amounts of material to complete the job. When working indoor and outdoor, floor-to-floor, large projects or small, the D2W Workhorse is the system for high productivity and profitability.

The D2W Workhorse features a high speed, effective mixing action that hydrates preblended materials while entrapping the optimal workability and boardlife. The water is metered directly into the system to achieve a constant water to cement ratio that ensures superior color uniformity, bond strength and compressive strength. It’s the simple, innovative material delivery system that mixes a wide range of products with incredible consistency, is easy to use, and cleans up in a minute or less. The D2W Workhorse is a contractor’s solution for locking in quality control and improving daily production!

The design and performance of the D2W Workhorse is the contractor solution for increased profitability. It allows you the opportunity to mix material within feet of your craftsmen—with minimal setup, labor and zero waste—while continuously producing a high quality mix. Weighing 210 pounds (95 kg) the D2W Workhorse moves about a jobsite like a wheelbarrow, can fit on a standard pallet, or can easily be transported in a pickup truck from job to job. It’s the portable mixing station designed for an endless list of products and project applications.

D2W Workhorse Specifications
SIZE• 67 in x 26.5 in x 42.5 in (170 cm x 67 cm x 108 cm)
Output (approximate)• Up to 1 pallet of preblended product / hour (over 1 yd³ / hour)
Capacity• Hopper holds up to 3 (80 lb) bags of preblended products
Product Requirements• Maximum aggregate size - 5/16 in (8 mm)
* Based on current configuration. Specifications may change slightly due to the model year of manufacture. Confirm specifications with your SPEC MIX representative.
SPEC MIX D2W Workhorse Continuous Mixing System

SUPPORT CENTER